/* https://github.com/BelfrySCAD/BOSL2 */ // ============================================================================ // Rafter drip ledge // ---------------------------------------------------------------------------- // A staple that grips a rafter: a band under the bottom face with a jaw up // each side face, one deck screw through each jaw. Water running down the // underside of the rafter reaches the band, crosses it and falls off its // downhill edge, so it stops trailing along the timber. // // The band hangs `thickness` proud of the bottom face and its edge is square. // That is far more than water can bridge (~3 mm), so the drip is reliable, and // the band is `thickness` wide along the rafter, which gives the water a // plateau to fall off rather than a corner to cling to. // // The jaws are bored from opposite sides at different heights - a quarter and // three quarters along the jaw - which is what keeps two long deck screws from // meeting in the middle of the rafter. With a 1.5" rafter and 1.5" screws the // tips do overshoot the mid-plane (the echo below prints by how much), so that // offset is doing real work: do not line the holes up. // // Built by sweeping a U, as before: // x away from the rafter's bottom face; -x is up the side faces // y across the rafter's width; the timber sits between the jaws // z along the rafter's length; the band is `thickness` wide there // // PRINT LYING EXACTLY AS MODELLED (z up). The part is an extrusion of the U // section, so every wall is vertical: no supports, no bridged roofs except the // two screw holes, and the perimeters run all the way round the U, which is // what carries the load. 54 x 70 mm footprint, 15.5 mm tall. // ============================================================================ include include /* [Rafter] */ // Width of the face the jaws grip: 1.5" for a rafter stood on its edge rafter_width = 38.1; // [30:0.1:60] // How far the jaws run up the side faces (1.5") jaw_height = 38.1; // [20:0.5:140] // Band and jaw thickness. Also the radius of the swept outer corners. thickness = 15; // [8:0.5:25] // Slip clearance per gripping face - a printed saddle is never a press fit clearance = 0.4; // [0:0.05:1.5] /* [Screw] */ // Overall length of the deck screw (1.5" = 38.1) screw_len = 38.1; // [25:0.5:90] // Clearance hole through the jaws hole_d = 6.5; // [4:0.1:9] // Head diameter that has to bear on the jaw's outer face head_d = 11; // [6:0.5:20] /* [Preview] */ // Translucent rafter timber - context only, never part of the print show_rafter = false; // Depth of that preview timber up the side faces (5.5") rafter_depth = 139.7; // [40:1:240] $fn = 64; // 100 was overkill: only the holes and two small // corner arcs are curved, and 64 facets is smooth inset = 0.5; // bead inset of the swept mask, as before // --------------------------------------------------------------------------- // Geometry // --------------------------------------------------------------------------- // The swept mask sits entirely outside the path, so the jaws' inner faces land // exactly `gap` apart - measured off the exported mesh, not assumed. Asking for // the rafter width plus clearance is therefore what you get. gap = rafter_width + 2 * clearance; wall = thickness + 2 * inset; // jaw thickness the screw passes // through, measured 16.0 path = turtle3d(["move", jaw_height, "arcright", inset, 90, "move", gap, "arcright", inset, 90, "move", jaw_height]); // Screws at a quarter and three quarters along the jaw, diagonally opposed. hole_lo_x = 0.25 * jaw_height; // near the jaw tips hole_hi_x = 0.75 * jaw_height; stagger = hole_hi_x - hole_lo_x; // how far apart the two screws // end up, up the side faces hole_z = (thickness + 2 * inset) / 2; // mid band, not mid mask // --------------------------------------------------------------------------- // Does the screw actually work? Checked, not hoped. // --------------------------------------------------------------------------- // The head bears on the jaw's outer face, so only screw_len - wall of the screw // reaches the wood. penetration = screw_len - wall; tip_overshoot = penetration - rafter_width / 2; // past the rafter's mid-plane edge_margin = hole_lo_x - hole_d / 2; // plastic outside the top hole corner_margin = jaw_height - hole_hi_x - hole_d / 2; assert(gap >= wall + 6, "jaws too thin for this rafter: a screw hole would break into the far jaw"); assert(head_d >= hole_d + 3, str("a ", head_d, " mm head has nothing to bear on around a ", hole_d, " mm hole: needs at least 1.5 mm of bearing all round")); assert(penetration >= 12, "too little screw reaches the timber: raise screw_len or drop thickness"); assert(edge_margin >= 3 && corner_margin >= 3, "the screw holes are too close to the jaw end or to the band: raise jaw_height"); assert(stagger >= hole_d + 4, "the two holes are too close together: raise jaw_height so they can be staggered further"); assert(tip_overshoot <= -2 || stagger >= head_d + 4, "the screws would meet in the middle: offset them further, or shorten them"); echo(str("fit: jaws ", fmt(gap), " mm apart for a ", fmt(rafter_width), " mm rafter (", fmt(clearance), " mm per face), band ", fmt(wall), " mm proud of the bottom face")); echo(str("screw: ", fmt(screw_len), " mm length less the ", fmt(wall), " mm jaw = ", fmt(penetration), " mm in the timber, tip ", tip_overshoot > 0 ? str("overshoots the mid-plane by ", fmt(tip_overshoot)) : str(fmt(-tip_overshoot), " short of the mid-plane"), ", holes ", fmt(stagger), " mm apart vertically")); echo(str("print: lying flat as modelled, ", fmt(jaw_height + wall), " x ", fmt(gap + 2 * wall), " mm footprint x ", fmt(wall), " mm tall, no supports; the two screw holes bridge ", fmt(wall), " mm")); if (tip_overshoot > 0) echo(str("NOTE: the screws pass each other's centreline - the ", fmt(stagger), " mm vertical offset is what stops them meeting. Keep the jaws square ", "to the timber when screwing on.")); function fmt(v) = round(v * 10) / 10; // --------------------------------------------------------------------------- // Part // --------------------------------------------------------------------------- difference() { path_sweep(mask2d_roundover(r = thickness, inset = inset), path); // Cutters long enough to leave nothing behind: an 0.5 mm skin of plastic // left on the far side of a jaw stops the screw head seating. // The swept mask sits entirely outside the path, so each jaw's material is // on the far side of its path line, away from the timber (measured: jaw 1 // spans y -0.5..15.5 about a path at y = 0, jaw 2 spans -55.4..-39.4 about a // path at y = -gap). Centring a cutter on the path, or running one right // across the part, drills one jaw properly and only nicks the other - which // is what the original did, leaving a blind hole. for (j = [[hole_lo_x, 0, 1], // jaw, its path y, which way it grows [hole_hi_x, -gap, -1]]) move([j[0], j[1] + j[2] * (wall / 2 - inset), hole_z]) ycyl(d = hole_d, h = wall + 4); } if (show_rafter) color("saddlebrown", 0.35) move([jaw_height - inset - rafter_depth / 2, -gap / 2 - inset, hole_z]) cuboid([rafter_depth, rafter_width, 120]);