Add Veer clip
This commit is contained in:
@@ -344,3 +344,11 @@ Model files:
|
|||||||
Model files:
|
Model files:
|
||||||
|
|
||||||
* tree-stand-floor-protector.scad
|
* tree-stand-floor-protector.scad
|
||||||
|
|
||||||
|
## veer-wagon-clip
|
||||||
|
|
||||||
|

|
||||||
|
|
||||||
|
Model files:
|
||||||
|
|
||||||
|
* veer-wagon-clip.scad
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
|
After Width: | Height: | Size: 36 KiB |
@@ -0,0 +1,267 @@
|
|||||||
|
// Vee-wagon beam clip — a C-shaped collar that wraps the octagonal beam
|
||||||
|
// section and carries a small integral loop for hanging things.
|
||||||
|
//
|
||||||
|
// See design-drawing.jpg. The pencil octagon is the beam cross-section:
|
||||||
|
// 24 mm across the narrow flats, 33 mm across the tall ones, with corner
|
||||||
|
// chamfers of about 4 x 9 mm (that is what the drawn 16 mm and 15 mm flats
|
||||||
|
// work out to). The marker line is the clip: it hugs three and a quarter
|
||||||
|
// sides of that section, opens across the narrow 24 mm direction, and
|
||||||
|
// finishes in a curled loop on the lower-left chamfer.
|
||||||
|
//
|
||||||
|
// Model space: Z = the beam axis, so the part comes off the bed in its
|
||||||
|
// print orientation — profile in XY, band standing up along Z.
|
||||||
|
// -Y = open (gap) side, +Y = closed back. The loop is not a separate boss:
|
||||||
|
// it is the band's own end curled over, tangent to the band's centreline.
|
||||||
|
//
|
||||||
|
// Why the section is octagonal and not round: a load on the loop pulls
|
||||||
|
// radially, which tries to rotate the clip about the beam axis. The flats
|
||||||
|
// react that torque, so the clip cannot spin — no screw, no glue.
|
||||||
|
// A load also stays inside the printed layers (it pulls along XY, never
|
||||||
|
// perpendicular to a bond line), which is the strong direction for FDM.
|
||||||
|
//
|
||||||
|
// Mounting — the beam has no free end, so the clip goes on sideways across the
|
||||||
|
// 24 mm flats and `gap` sets the bite: 23.8 presses on, 24.4 slips on.
|
||||||
|
// `grip` would hook the plain tail behind the flat for a captive fit, but then
|
||||||
|
// the opening ends up narrower than the section and the clip could only be
|
||||||
|
// slid on from a free end. Keep it at 0 here.
|
||||||
|
//
|
||||||
|
// Prints flat with no supports: every wall is vertical and the tallest
|
||||||
|
// feature is the band height.
|
||||||
|
|
||||||
|
include <BOSL2/std.scad>
|
||||||
|
|
||||||
|
/* [Beam] */
|
||||||
|
// Beam across-flats, narrow direction (X)
|
||||||
|
beam_w = 23;
|
||||||
|
// Beam across-flats, tall direction (Y)
|
||||||
|
beam_h = 33;
|
||||||
|
// Corner chamfer along X (24 - 2*4 = 16 mm chamfer-free flats)
|
||||||
|
beam_chamf_x = 4; // [0:0.5:10]
|
||||||
|
// Corner chamfer along Y (33 - 2*9 = 15 mm chamfer-free flats)
|
||||||
|
beam_chamf_y = 9; // [0:0.5:14]
|
||||||
|
// Radial clearance between the beam and the clip bore
|
||||||
|
fit = 0.3; // [0:0.05:1]
|
||||||
|
|
||||||
|
/* [Clip] */
|
||||||
|
// Band wall thickness, normal to the beam faces
|
||||||
|
wall = 2; // [1.5:0.25:8]
|
||||||
|
// Band height along the beam axis
|
||||||
|
band_h = 10; // [4:1:30]
|
||||||
|
// How much further the plain tail (the side without the loop) reaches round
|
||||||
|
// the corner towards the edge of the flat, so it hooks over the section. Any
|
||||||
|
// more than about 1 mm makes the opening narrower than the section, which means
|
||||||
|
// the clip can only be slid on from a free end of the beam — this beam has
|
||||||
|
// none, so leave this at 0 and take the grip from `gap` instead.
|
||||||
|
grip = 0; // [0:0.5:8]
|
||||||
|
// Flex clearance between the two ends of the opening on the -Y side.
|
||||||
|
// 23.8 the band presses on with 0.2 mm of bite
|
||||||
|
// 24.4 loose: rock free, and free to slide along the beam
|
||||||
|
// 0 no opening at all, a plain collar (strongest)
|
||||||
|
// Open this up in 0.2 mm steps if the clip will not seat.
|
||||||
|
gap = 23.8; // [0:0.2:34]
|
||||||
|
|
||||||
|
/* [Loop] */
|
||||||
|
// Loop overall width across the curl (10 mm on the drawing)
|
||||||
|
loop_d = 10; // [8:0.5:20]
|
||||||
|
// Throat between the hook's tip and the band — how big a thing you can slip
|
||||||
|
// on. 0 closes the crook into a ring instead.
|
||||||
|
mouth = 5; // [0:0.5:9]
|
||||||
|
// Which face of the section the loop grows off, as the outward normal angle of
|
||||||
|
// that face: 205 = the lower chamfer it continues, 180 = the narrow flat. The
|
||||||
|
// nearest face is used and the hook squares up to it.
|
||||||
|
loop_ang = 205; // [0:5:355]
|
||||||
|
// Slide the loop along that face: 0 centres it on the face, + is towards the
|
||||||
|
// opening, - is away from it.
|
||||||
|
loop_off = 2; // [-12:0.5:12]
|
||||||
|
// Which way the curl winds: 1 lays the throat back along the band towards the
|
||||||
|
// section, as drawn; -1 mirrors it to the other side.
|
||||||
|
hook_dir = 1; // [1,-1]
|
||||||
|
// How far before the tip the ribbon tapers to its point
|
||||||
|
hook_taper = 40; // [0:5:90]
|
||||||
|
|
||||||
|
/* [Hidden] */
|
||||||
|
// Preview aid: draw the beam in the render so the fit can be eyeballed.
|
||||||
|
// Leave off when exporting for the slicer.
|
||||||
|
show_beam = false;
|
||||||
|
|
||||||
|
$fn = 256;
|
||||||
|
epsilon = 0.01;
|
||||||
|
layer_height = 0.2; // general utility print; not a Customizer parameter
|
||||||
|
|
||||||
|
// The only dimension that prints along the build axis — snap it to layers.
|
||||||
|
band_h_l = ceil(band_h / layer_height) * layer_height;
|
||||||
|
|
||||||
|
// Round for display in the echoes below (BOSL2 shadows round()'s 2-arg form).
|
||||||
|
function r1(v) = round(v*10)/10;
|
||||||
|
function r2(v) = round(v*100)/100;
|
||||||
|
|
||||||
|
// Octagon: across-flats w x h, corners cut back chx x chy.
|
||||||
|
function octagon(w, h, chx, chy) = [
|
||||||
|
[-w/2 + chx, h/2],
|
||||||
|
[ w/2 - chx, h/2],
|
||||||
|
[ w/2, h/2 - chy],
|
||||||
|
[ w/2, -h/2 + chy],
|
||||||
|
[ w/2 - chx, -h/2],
|
||||||
|
[-w/2 + chx, -h/2],
|
||||||
|
[-w/2, -h/2 + chy],
|
||||||
|
[-w/2, h/2 - chy],
|
||||||
|
];
|
||||||
|
|
||||||
|
// Bore = beam section grown by the clearance on every face.
|
||||||
|
hw = beam_w / 2 + fit;
|
||||||
|
hh = beam_h / 2 + fit;
|
||||||
|
chx = beam_chamf_x + fit;
|
||||||
|
chy = beam_chamf_y + fit;
|
||||||
|
BORE = octagon(2*hw, 2*hh, chx, chy);
|
||||||
|
|
||||||
|
// Outer contour = bore pushed out by the wall, joins rounded off by the same
|
||||||
|
// amount so the band has no sharp outer corners.
|
||||||
|
OUTER = offset(BORE, delta=wall, closed=true);
|
||||||
|
|
||||||
|
// Each bore face as [outward normal angle, distance from the beam centre].
|
||||||
|
FACES = [
|
||||||
|
for (i = idx(BORE))
|
||||||
|
let(p1 = BORE[i], p2 = BORE[(i + 1) % len(BORE)], e = p2 - p1,
|
||||||
|
n = unit([-e.y, e.x]))
|
||||||
|
[atan2(n.y, n.x), p1 * n]
|
||||||
|
];
|
||||||
|
|
||||||
|
// How far out the bore is along a ray at `ang`.
|
||||||
|
function ray_out(faces, ang) =
|
||||||
|
min([for (f = faces) let(c = cos(ang - f[0])) c > 1e-6 ? f[1] / c : 1e9]);
|
||||||
|
|
||||||
|
// The hook is the band's own end curled into a crook: the ribbon is the band's
|
||||||
|
// thickness and its centreline is tangent to the band's centreline, so the two
|
||||||
|
// read as one stroke and the root cross-section lines up exactly with the
|
||||||
|
// band's. The crook starts where it meets the band and sweeps round until the
|
||||||
|
// tip is `mouth` away from it, which is what sets the sweep:
|
||||||
|
// throat = 2 * hook_ri * sin(sweep_shortfall / 2)
|
||||||
|
hook_ro = loop_d / 2; // curl outside
|
||||||
|
hook_ri = hook_ro - wall; // curl inside; ribbon = the band
|
||||||
|
hook_rc = hook_ro - wall / 2; // curl centreline
|
||||||
|
hook_tp = mouth > 0 ? hook_taper : 0;
|
||||||
|
hook_dw = mouth > 0 ? 2 * asin(min(0.98, mouth / (2 * hook_ri))) : 0;
|
||||||
|
hook_span = 360 - hook_dw; // the ribbon's sweep
|
||||||
|
// The face the hook grows off. `loop_ang` only *picks* the face; the hook then
|
||||||
|
// squares up to that face's own normal. The root has to be anchored on the
|
||||||
|
// face itself rather than on the foot of the perpendicular from the beam
|
||||||
|
// centre: that foot falls off the end of a chamfer, which put the root on the
|
||||||
|
// bore's corner and made the band's end cut slice diagonally through it.
|
||||||
|
face_off = [for (f = FACES) abs(((f[0] - loop_ang + 540) % 360) - 180)];
|
||||||
|
face_i = [for (i = idx(face_off)) if (face_off[i] == min(face_off)) i][0];
|
||||||
|
hook_ang = FACES[face_i][0]; // the face's own normal angle
|
||||||
|
hook_n = [cos(hook_ang), sin(hook_ang)];
|
||||||
|
hook_t = [cos(hook_ang + 90), sin(hook_ang + 90)];
|
||||||
|
// The root is a point on the face, slid along it by `loop_off`, so the ribbon's
|
||||||
|
// root cross-section lands exactly in the band's wall.
|
||||||
|
hook_root = (BORE[face_i] + BORE[(face_i + 1) % len(BORE)]) / 2
|
||||||
|
+ hook_t * loop_off;
|
||||||
|
loop_c = hook_root + hook_n * (wall / 2 + hook_rc);
|
||||||
|
loop_nd = hook_root * hook_n;
|
||||||
|
hook_a0 = hook_ang + 180; // where the ribbon meets the band
|
||||||
|
|
||||||
|
function hook_out_r(a) =
|
||||||
|
hook_ro - (hook_tp > 0
|
||||||
|
? (hook_ro - hook_ri - 0.8)
|
||||||
|
* min(1, max(0, (a - (hook_span - hook_tp)) / hook_tp))
|
||||||
|
: 0);
|
||||||
|
|
||||||
|
// The crook's outline: out along the curl tapering into the tip, back along
|
||||||
|
// the barrel, closed off flat where it runs into the band.
|
||||||
|
hook_seg = ceil(hook_span / 2);
|
||||||
|
HOOK = [
|
||||||
|
for (i = [0 : hook_seg])
|
||||||
|
let(a = hook_span * i / hook_seg)
|
||||||
|
loop_c + polar_to_xy(hook_out_r(a), hook_a0 - hook_dir * a),
|
||||||
|
for (i = [hook_seg : -1 : 0])
|
||||||
|
let(a = hook_span * i / hook_seg)
|
||||||
|
loop_c + polar_to_xy(hook_ri, hook_a0 - hook_dir * a)
|
||||||
|
];
|
||||||
|
|
||||||
|
// The opening keeps its `gap` flex clearance but is shifted over by `grip`
|
||||||
|
// towards the loop, which leaves the plain tail hooked under the flat.
|
||||||
|
open_l = -(gap / 2 + grip); // x of the opening's loop-side face
|
||||||
|
open_r = gap / 2 - grip; // x of the plain tail's inner face
|
||||||
|
cut_h = beam_h + 2 * wall;
|
||||||
|
|
||||||
|
echo(str("Beam section: ", beam_w, " x ", beam_h, " mm, chamfer ",
|
||||||
|
beam_chamf_x, " x ", beam_chamf_y, " -> flats ",
|
||||||
|
beam_w - 2*beam_chamf_x, " / ", beam_h - 2*beam_chamf_y, " mm"));
|
||||||
|
echo(str("Bore: ", 2*hw, " x ", 2*hh, " mm. Band ", wall, " mm thick x ",
|
||||||
|
band_h_l, " mm high = ", band_h_l/layer_height, " layers"));
|
||||||
|
echo(str("Opening ", gap, " mm -> ", gap == 0 ? "no opening, plain collar" :
|
||||||
|
gap > beam_w ? str(r2(gap-beam_w), " mm clearance") :
|
||||||
|
gap < beam_w ? str(r2(beam_w-gap), " mm bite") :
|
||||||
|
"zero clearance",
|
||||||
|
grip > 0 ? str("; tail reaches ", grip, " mm further round the corner",
|
||||||
|
" (needs a free end to mount)") :
|
||||||
|
" presses on sideways across the flats"));
|
||||||
|
echo(str("Hook: ", loop_d, " mm across a ", wall, " mm ribbon, ",
|
||||||
|
r2(2*hook_ri), " mm barrel, ", r1(hook_span), " deg of curl, ",
|
||||||
|
mouth > 0 ? str(mouth, " mm throat") : "closed ring",
|
||||||
|
" centred ", r1(loop_c.x), ", ", r1(loop_c.y),
|
||||||
|
" (", r1(loop_nd + wall/2 + hook_rc), " mm out, tangent to the band)"));
|
||||||
|
|
||||||
|
// Flat profile of the clip, then one extrusion along the beam axis.
|
||||||
|
module clip_profile() {
|
||||||
|
difference() {
|
||||||
|
union() {
|
||||||
|
// Band: an octagonal sleeve, opened up on the -Y side. Shifting
|
||||||
|
// the opening towards the loop lets the plain tail reach further
|
||||||
|
// round the corner by `grip`.
|
||||||
|
difference() {
|
||||||
|
polygon(OUTER);
|
||||||
|
polygon(BORE);
|
||||||
|
if (gap > epsilon) {
|
||||||
|
// square() is anchored on its low corner, so the cutter
|
||||||
|
// reaches from the bore's -Y face out past the part.
|
||||||
|
translate([open_l - epsilon, -hh - cut_h])
|
||||||
|
square([gap + 2*epsilon, cut_h]);
|
||||||
|
}
|
||||||
|
// Stop the band dead at the hook's root so nothing carries on
|
||||||
|
// past the curl. Two things to get right here: a flat cut
|
||||||
|
// leaves the band's end wall standing outboard of the curl as a
|
||||||
|
// loose-looking tab (the curl only reaches the band's outer face
|
||||||
|
// 4 mm further along), and cutting to the curl's *circle* leaves
|
||||||
|
// a crescent of band by the bore that ends in a barb, because
|
||||||
|
// that circle is tangent to the bore side. So keep exactly the
|
||||||
|
// ribbon's own footprint, grown by half an epsilon to keep the
|
||||||
|
// union off coincident faces.
|
||||||
|
difference() {
|
||||||
|
translate(hook_root) rotate(hook_ang + 90)
|
||||||
|
translate([0, -(wall + 8)])
|
||||||
|
square([beam_h, wall + 9]);
|
||||||
|
polygon(offset(HOOK, delta=epsilon/2, closed=true));
|
||||||
|
}
|
||||||
|
}
|
||||||
|
// The hook: the band's end curled into a crook, tangent to the
|
||||||
|
// band's centreline so the two read as one stroke.
|
||||||
|
polygon(HOOK);
|
||||||
|
}
|
||||||
|
// Nothing may stand inside the beam's envelope.
|
||||||
|
polygon(BORE);
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
// The clip: the profile swept along the beam axis by the band height.
|
||||||
|
module clip() {
|
||||||
|
linear_extrude(band_h_l)
|
||||||
|
clip_profile();
|
||||||
|
}
|
||||||
|
|
||||||
|
// The beam itself, for in-context checking only — never print this.
|
||||||
|
module beam() {
|
||||||
|
color("tan")
|
||||||
|
linear_extrude(band_h_l + 20, center=true)
|
||||||
|
polygon(octagon(beam_w, beam_h, beam_chamf_x, beam_chamf_y));
|
||||||
|
}
|
||||||
|
|
||||||
|
// One object for the slicer
|
||||||
|
union() {
|
||||||
|
clip();
|
||||||
|
}
|
||||||
|
|
||||||
|
// Beam in context, for previewing the fit only.
|
||||||
|
if (show_beam) {
|
||||||
|
beam();
|
||||||
|
}
|
||||||
File diff suppressed because it is too large
Load Diff
Reference in New Issue
Block a user